How to Clean Industrial Epoxy Floors In San Diego

Warehouses, walkways, roads, garages, factories, and other industrial floors are subjected to a great deal of wear and tear. As a result, they wear out more quickly and get dirty more frequently. They deal with a wide range of issues, including foot traffic, mechanical movements, tool drops, chemical spills, and more. As a result, choosing the finest flooring material is critical. Over the years, industrial epoxy has shown to be an effective flooring option for several floor types. This is because epoxy is a long-lasting, easy-to-clean, and maintained substance.

Like any other floor, industrial epoxy flooring should be cleaned and maintained regularly to withstand the traffic and pressure they are subjected to. Here’s how Southside Epoxy can assist property owners with epoxy floor cleaning.

Clean Away The Debris

Debris might be found on the surfaces of your industrial property, depending on where it is located and what it is used for. Papers and leaves can be blown to your home by the wind, and some of the trash may be transported on vehicle tires or even your shoes. They will crumble and turn into the soil if you leave them alone, posing additional obstacles. Pick up the leaves and tidy up the little things that have accumulated on your floor. Make sure you dispose of them properly.

Sweep And Mop Dirt And Grit

Sweeping and mopping may appear simple, but few people realize how critical removing dirt and grit from floor surfaces is. You’ll make scratches and embed dirt into the floor if you walk around, drive vehicles, operate machines, and carry bags on and off the floor. Aside from leaving scars on the surfaces, this is also where the floor’s dullness begins. Depending on how readily dirt and grit accumulate on your floors, you should design a cleaning plan for your industrial epoxy.

Vacuuming is the finest approach to removing debris from industrial epoxy surfaces. This procedure is more efficient than the manual method in terms of cleaning. You save a significant amount of time, which is crucial in a commercial setting. To avoid scratching the floor surfaces, your vacuum should have a soft brush connected. Be cautious, especially if you’re going to move something.

Spot Clean Whenever There’s Soiling

Clean on the Spot Whenever Accidents do happen, you could spill grease, coffee, or anything else on your floor. If this occurs, do not wait until the next planned cleaning time to clean it. Rather, rapidly clean up the mess by sweeping, vacuuming, or mopping it up. On the other hand, industrial epoxy is resistant to most soiling and cleans off quickly and easily. You can sweep solids and mop away everything that is water-based. Vacuuming is the quickest solution yet again.

If there are chemical spills, make sure you follow the manufacturer’s instructions to keep everyone safe during spot cleaning.

When The Soiling Needs Thorough Cleaning

Perhaps you’ve recently moved into a new warehouse and need to clean the flooring before you can begin utilizing it. The floors, however, haven’t been cleaned in a long time and are badly dirty. Start by getting rid of anything that could get in the way of the cleaning procedure. Get rid of whatever you can see, even the trash. Sweep and vacuum the whole floor to remove any loose particles that may have accumulated on the surface.

Then scrape away the trapped filth and grime with a hard form mop and warm water. As much as possible, keep the floor clean. Then combine water and ammonia in a container (for every gallon of hot water, use three ounces of ammonia). That should be enough to remove all of the discolorations and restore the epoxy floor’s luster.

Don’t Use Soap-Based Cleaners

Because soap is readily available and works well for other floor treatments, it may be tempting to clean industrial epoxy floors with it. But you shouldn’t because soap causes a haze on the floor that builds up over time and eventually covers the sheen of your flooring. Choose a gentle soap with a neutral PH to scrape away the worst stains if you must use soap. To ensure that you do not cause aesthetic harm to your floor, properly clear away any residue left behind.

Get Rid Of Stains

Though epoxy is stain-resistant, rust and other sorts of stains may appear in some locations if it is mishandled. Rust stains, for example, require some scrubbing to remove off surfaces. Scrub the stain with a scouring sponge and warm water until the stain disappears. Because strong chemicals like comets and abrasives like steel wool might harm the floor, you shouldn’t use them. Also, stay away from any cleaning products that include citrus or acids. These don’t only scrape the surface of your floor; they also react with the epoxy catalysts, causing the floor to be damaged.

Don’t Allow Car Chemicals, Oils, And Other Chemicals To Stay Too Long

If you deal with chemicals like paint or home cleansers on your industrial epoxy floor, there’s a good potential that chemicals, gas, or motor oils may spill on it. The easiest method to cope with them is to clear them up as soon as you see them. Chemicals have a tendency to react with floor surfaces, denting or entirely damaging them if they do. Shop towels are ideal for this. However, as previously stated, be sure you know which chemical you’re dealing with and how to manage it properly to avoid harming yourself or others.

Protect The Floor Against Damage

While we trust industrial epoxy to be incredibly durable and easy to clean, it’s critical to avoid unwanted soiling and damage. For example, if your floor or a portion of it is used for welding projects, you should cover it with welding mats to preserve it in good condition. If your floor is subjected to large loads, plywood should be used to protect it. Contact us today at Concrete Polishing Solutions for concrete polishing services.

Should Industrial Epoxy Peel Or Chip?

A correctly built epoxy floor should never crack or peel in the ideal situation. It chemically adheres to the concrete surface and cures to produce an extremely durable coating that should never dent if cleaned and maintained properly. The contractor that installs your industrial epoxy should propose high-quality epoxy resins and install them properly. The concrete slab must be ground down and adequately prepared prior to epoxy application for optimum results.

Invite Concrete Polishing Solutions To Install And Clean Industrial Epoxy

It’s a terrific idea to use epoxy for flooring your business or industrial area. All you have to do now is make sure the high-quality epoxy goods are correctly put to withstand the intensive labor and traffic you anticipate on your site. Cleaning and maintaining your flooring should be simple if the installation is done correctly. We provide both installation and cleaning services at Concrete Polishing Solutions. Our professional personnel, industrial-grade equipment, and years of successful work set us apart.

Our Complete Services

Concrete Polishing

• Acid Staining
• Concrete Overlay
• Concrete Repair
• Concrete Resurfacing
• Concrete Sealing
• Self Leveling

Epoxy Flooring

• Acrylic Flooring
• Metallic Epoxy Flooring
• Epoxy Chip Flooring
• Epoxy Quartz Flooring
• Solid Epoxy Flooring
• Urethane Cement
• Polyurea Polyaspartic

Concrete Caulking/Waterproofing

• Control Joint Caulking
• Elastomeric Wall Coatings
• Expansion Joint Caulking
• Silicone Caulking
• Urethane Caulking
• Waterproofing
• Wet Glazing

Commercial Applications

• Commercial
• Auto Dealerships
• Corporate Offices
• Government
• Hotels
• Manufacturing
• Parking Structures
• Retail Stores
• Sports Facilities

• Commercial Kitchen
• Factories
• Hospitals
• Industrial
• Military
• Restaurants
• Schools
• Warehouses

Residential Applications

• Residential Applications
• Basements
• Driveways
• Garage Floors
• Interior Floors
• Patios
• Pool Decks